國立虎尾科技大學 |

Laser Based Powder Bed Fusion of Plain Carbon and Low-Alloy Steels: Microstructure and Processability.

紀錄類型:	書目-語言資料,印刷品 : Monograph/item
正題名/作者:	Laser Based Powder Bed Fusion of Plain Carbon and Low-Alloy Steels: Microstructure and Processability./
作者:	Hearn, William.
出版者:	Ann Arbor : ProQuest Dissertations & Theses, : 2021,
面頁冊數:	55 p.
附註:	Source: Dissertations Abstracts International, Volume: 83-07, Section: B.
Contained By:	Dissertations Abstracts International83-07B.
標題:	Mechanical properties. -
電子資源:	http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=28829438
ISBN:	9798496570237

Laser Based Powder Bed Fusion of Plain Carbon and Low-Alloy Steels: Microstructure and Processability.
Hearn, William.

Laser Based Powder Bed Fusion of Plain Carbon and Low-Alloy Steels: Microstructure and Processability. - Ann Arbor : ProQuest Dissertations & Theses, 2021 - 55 p.

Source: Dissertations Abstracts International, Volume: 83-07, Section: B.

Thesis (Lic.Eng)--Chalmers Tekniska Hogskola (Sweden), 2021.

This item must not be sold to any third party vendors.

Despite the prominence of laser based powder bed fusion (LB-PBF) as an additive manufacturing technique, the number of alloys that have been approved for the process remains limited. In traditional manufacturing, ferrous alloys are the most common alloy group, consisting primarily of plain carbon and low-alloy steels. However, in LB-PBF, the production of ferrous alloys is limited to a small number of austenitic/precipitation-hardened stainless steels and tool steels. The lack of plain carbon and low-alloy steels stems from the negative impacts of carbon during processing, which promotes the formation of cracking defects within the as-built material. Hence, to expand the opportunities of LB-PBF, an understanding of how to process these carbon-containing ferrous alloys must be established.This work addresses the LB-PBF processability and microstructure of various plain carbon (0.06 to 1.1 wt.% C) and low-alloy steels (4130, 4140, 4340 and 8620). Microstructural analysis found the as-built specimens to consist of tempered martensite that formed due to the initial rapid cooling and subsequent intrinsic heat treatment that takes place during LB-PBF. Additionally, the presence of retained austenite was observed in alloys with ≥0.75 wt.% C and was caused by the depression of the martensite transformation temperatures, which left some austenite untransformed when cooling to room temperature.In terms of defects, porosity within the as-built specimens could be related to the chosen volumetric energy density (VED) and the carbon content of the alloy. At low VEDs, specimens contained large, irregular pores that related to lack of fusion porosity, while at high VEDs, specimens contained rounded, medium-sized pores that related to keyhole porosity. In terms of carbon content, increasing the amount of carbon was found to reduce the amount lack of fusion porosity at low VEDs while increasing the amount of keyhole porosity at higher VEDs. The decrease in lack of fusion porosity was caused by the improved wettability and flowability of the melt pool, while the increase in keyhole porosity was caused by increase in melt pool depth with higher carbon contents.Besides porosity, cold cracking was observed in some plain carbon and low-alloy steels, forming in specimens with a hardness above certain thresholds: ≥425 HV for Fe-C alloys, >460 HV for 4140 alloys and >500 HV for 4340 alloys. Increasing the VED or the laser power decreased the specimen hardness as both factors enhanced the intrinsic heat treatment of LB-PBF. This meant that cracking (in some alloys) could be avoided if a large enough VED or laser power was used. The carbon content also affected the as-built specimen hardness and thus the cracking susceptibility, a finding that explains why low carbon alloys (<0.43 wt.% C) did not display cracking at any of the tested VEDs, whereas high carbon alloys (≥0.75 wt.% C) displayed cracking at every tested VED. Using these findings, processing windows were established that produced high-density (>99.8%), defect-free plain carbon and low-alloy steel specimens without the requirement of build plate preheating.

ISBN: 9798496570237Subjects--Topical Terms:

1004682
Mechanical properties.

Laser Based Powder Bed Fusion of Plain Carbon and Low-Alloy Steels: Microstructure and Processability.
LDR:04310nam a2200361 4500 001 1067271
005 20220823142333.5
008 221020s2021 ||||||||||||||||| ||eng d
020 $a 9798496570237
035 $a (MiAaPQ)AAI28829438
035 $a (MiAaPQ)Chalmers_SE522034
035 $a AAI28829438
040 $a MiAaPQ $c MiAaPQ
100 1 $a Hearn, William. $3 1372791
245 1 0 $a Laser Based Powder Bed Fusion of Plain Carbon and Low-Alloy Steels: Microstructure and Processability.
260 1 $a Ann Arbor : $b ProQuest Dissertations & Theses, $c 2021
300 $a 55 p.
500 $a Source: Dissertations Abstracts International, Volume: 83-07, Section: B.
500 $a Advisor: Hryha, Eduard;Nyborg , Lars .
502 $a Thesis (Lic.Eng)--Chalmers Tekniska Hogskola (Sweden), 2021.
506 $a This item must not be sold to any third party vendors.
520 $a Despite the prominence of laser based powder bed fusion (LB-PBF) as an additive manufacturing technique, the number of alloys that have been approved for the process remains limited. In traditional manufacturing, ferrous alloys are the most common alloy group, consisting primarily of plain carbon and low-alloy steels. However, in LB-PBF, the production of ferrous alloys is limited to a small number of austenitic/precipitation-hardened stainless steels and tool steels. The lack of plain carbon and low-alloy steels stems from the negative impacts of carbon during processing, which promotes the formation of cracking defects within the as-built material. Hence, to expand the opportunities of LB-PBF, an understanding of how to process these carbon-containing ferrous alloys must be established.This work addresses the LB-PBF processability and microstructure of various plain carbon (0.06 to 1.1 wt.% C) and low-alloy steels (4130, 4140, 4340 and 8620). Microstructural analysis found the as-built specimens to consist of tempered martensite that formed due to the initial rapid cooling and subsequent intrinsic heat treatment that takes place during LB-PBF. Additionally, the presence of retained austenite was observed in alloys with ≥0.75 wt.% C and was caused by the depression of the martensite transformation temperatures, which left some austenite untransformed when cooling to room temperature.In terms of defects, porosity within the as-built specimens could be related to the chosen volumetric energy density (VED) and the carbon content of the alloy. At low VEDs, specimens contained large, irregular pores that related to lack of fusion porosity, while at high VEDs, specimens contained rounded, medium-sized pores that related to keyhole porosity. In terms of carbon content, increasing the amount of carbon was found to reduce the amount lack of fusion porosity at low VEDs while increasing the amount of keyhole porosity at higher VEDs. The decrease in lack of fusion porosity was caused by the improved wettability and flowability of the melt pool, while the increase in keyhole porosity was caused by increase in melt pool depth with higher carbon contents.Besides porosity, cold cracking was observed in some plain carbon and low-alloy steels, forming in specimens with a hardness above certain thresholds: ≥425 HV for Fe-C alloys, >460 HV for 4140 alloys and >500 HV for 4340 alloys. Increasing the VED or the laser power decreased the specimen hardness as both factors enhanced the intrinsic heat treatment of LB-PBF. This meant that cracking (in some alloys) could be avoided if a large enough VED or laser power was used. The carbon content also affected the as-built specimen hardness and thus the cracking susceptibility, a finding that explains why low carbon alloys (<0.43 wt.% C) did not display cracking at any of the tested VEDs, whereas high carbon alloys (≥0.75 wt.% C) displayed cracking at every tested VED. Using these findings, processing windows were established that produced high-density (>99.8%), defect-free plain carbon and low-alloy steel specimens without the requirement of build plate preheating.
590 $a School code: 0419.
650 4 $a Mechanical properties. $3 1004682
650 4 $a Heat transfer. $3 1085480
650 4 $a Raw materials. $3 1113584
650 4 $a Heat treating. $3 1372793
650 4 $a Cooling. $3 812392
650 4 $a Titanium alloys. $3 811066
650 4 $a Defects. $3 1372731
650 4 $a Solidification. $3 685755
650 4 $a Residual stress. $3 1083680
650 4 $a Lasers. $3 557748
650 4 $a Carbon. $3 557161
650 4 $a Temperature. $3 1015941
650 4 $a Stainless steel. $3 716611
650 4 $a Particle size. $3 1372794
650 4 $a Grain size. $3 1372521
650 4 $a Atoms & subatomic particles. $3 1372795
650 4 $a Atomic physics. $3 1182532
650 4 $a Biology. $3 599573
650 4 $a Materials science. $3 557839
650 4 $a Mechanics. $3 527684
650 4 $a Optics. $3 595336
650 4 $a Physics. $3 564049
690 $a 0748
690 $a 0306
690 $a 0794
690 $a 0346
690 $a 0752
690 $a 0605
710 2 $a Chalmers Tekniska Hogskola (Sweden). $3 1372792
773 0 $t Dissertations Abstracts International $g 83-07B.
790 $a 0419
791 $a Lic.Eng
792 $a 2021
793 $a English
856 4 0 $u http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=28829438