國立虎尾科技大學 |

Development of grinding models for brittle materials.

紀錄類型:	書目-語言資料,手稿 : Monograph/item
正題名/作者:	Development of grinding models for brittle materials./
作者:	Sharp, Keith Wayne.
面頁冊數:	1 online resource (140 pages)
附註:	Source: Dissertations Abstracts International, Volume: 60-08, Section: B.
Contained By:	Dissertations Abstracts International60-08B.
標題:	Materials science. -
電子資源:	click for full text (PQDT)
ISBN:	9780599022041

Development of grinding models for brittle materials.
Sharp, Keith Wayne.

Development of grinding models for brittle materials. - 1 online resource (140 pages)

Source: Dissertations Abstracts International, Volume: 60-08, Section: B.

Thesis (Ph.D.)--North Carolina State University, 1998.

Includes bibliographical references

Accurate prediction of the onset of fracture during the grinding of brittle materials would enable parts to be made with little or no subsurface damage. The fracture mechanics of an indentation test provides a model for the behavior of brittle materials. During an indentation test, a critical depth exists where the energy of new surface formation becomes less than the energy of plastic deformation and the material begins to fracture. In grinding the critical infeed per revolution is an order of magnitude less than the critical indentation depth. For grinding, the indenters are the grit randomly dispersed in the grinding wheel. Determination of the individual depth of cut of the grit requires relating the distribution of the grit to the surface of the workpiece and the desired infeed. This research develops an analytic model which solves for the depth of cut using the statistics of a random distribution of grit cutting a surface. Two distinct cutting regimes can be identified. At extremely low infeeds the grain depth of cut is equal to the infeed, but as the infeed is increased the depth of cut becomes less than the infeed. Using this model as a baseline, the relation of the specific grinding energy μg to the grit depth of cut was developed for ductile regime grinding with spherical grit. In the ductile regime, at nanometer level infeeds per revolution μg was predicted to have a negative power law relation to the depth of cut. Plunge grinding experiments were conducted on BK7, CVD SiC, and silicon, which measured the cutting and normal forces in-situ and the workpiece surfaces after the tests. A method of determining μg for each revolution of the wheel was developed. For each of the plunge grinding tests, μg had a minimum value corresponding to the as-dressed wear state of the grit. The minimum μg values confirmed the negative power law relation of μg to the depth of cut in the ductile regime and found that μg is no longer a function of the depth of cut in the brittle regime. The transitions infeed rates identified by minimum μg were verified by optical and surface roughness measurements of the workpiece surfaces.

Electronic reproduction.
Ann Arbor, Mich. :
ProQuest,
2024

Mode of access: World Wide Web

ISBN: 9780599022041Subjects--Topical Terms:

557839
Materials science.
Subjects--Index Terms:

Brittle materialsIndex Terms--Genre/Form:

554714
Electronic books.

Development of grinding models for brittle materials.
LDR:03495ntm a22003857 4500 001 1148486
005 20240924101525.5
006 m o d
007 cr bn ---uuuuu
008 250605s1998 xx obm 000 0 eng d
020 $a 9780599022041
035 $a (MiAaPQ)AAI9904939
035 $a AAI9904939
040 $a MiAaPQ $b eng $c MiAaPQ $d NTU
100 1 $a Sharp, Keith Wayne. $3 1474456
245 1 0 $a Development of grinding models for brittle materials.
264 0 $c 1998
300 $a 1 online resource (140 pages)
336 $a text $b txt $2 rdacontent
337 $a computer $b c $2 rdamedia
338 $a online resource $b cr $2 rdacarrier
500 $a Source: Dissertations Abstracts International, Volume: 60-08, Section: B.
500 $a Publisher info.: Dissertation/Thesis.
500 $a Advisor: Scattergood, Ronald O.
502 $a Thesis (Ph.D.)--North Carolina State University, 1998.
504 $a Includes bibliographical references
520 $a Accurate prediction of the onset of fracture during the grinding of brittle materials would enable parts to be made with little or no subsurface damage. The fracture mechanics of an indentation test provides a model for the behavior of brittle materials. During an indentation test, a critical depth exists where the energy of new surface formation becomes less than the energy of plastic deformation and the material begins to fracture. In grinding the critical infeed per revolution is an order of magnitude less than the critical indentation depth. For grinding, the indenters are the grit randomly dispersed in the grinding wheel. Determination of the individual depth of cut of the grit requires relating the distribution of the grit to the surface of the workpiece and the desired infeed. This research develops an analytic model which solves for the depth of cut using the statistics of a random distribution of grit cutting a surface. Two distinct cutting regimes can be identified. At extremely low infeeds the grain depth of cut is equal to the infeed, but as the infeed is increased the depth of cut becomes less than the infeed. Using this model as a baseline, the relation of the specific grinding energy μg to the grit depth of cut was developed for ductile regime grinding with spherical grit. In the ductile regime, at nanometer level infeeds per revolution μg was predicted to have a negative power law relation to the depth of cut. Plunge grinding experiments were conducted on BK7, CVD SiC, and silicon, which measured the cutting and normal forces in-situ and the workpiece surfaces after the tests. A method of determining μg for each revolution of the wheel was developed. For each of the plunge grinding tests, μg had a minimum value corresponding to the as-dressed wear state of the grit. The minimum μg values confirmed the negative power law relation of μg to the depth of cut in the ductile regime and found that μg is no longer a function of the depth of cut in the brittle regime. The transitions infeed rates identified by minimum μg were verified by optical and surface roughness measurements of the workpiece surfaces.
533 $a Electronic reproduction. $b Ann Arbor, Mich. : $c ProQuest, $d 2024
538 $a Mode of access: World Wide Web
650 4 $a Materials science. $3 557839
650 4 $a Mechanical engineering. $3 557493
650 4 $a Mechanics. $3 527684
653 $a Brittle materials
653 $a Fracture
653 $a Grinding
655 7 $a Electronic books. $2 local $3 554714
690 $a 0794
690 $a 0548
690 $a 0346
710 2 $a ProQuest Information and Learning Co. $3 1178819
710 2 $a North Carolina State University. $3 845424
773 0 $t Dissertations Abstracts International $g 60-08B.
856 4 0 $u http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=9904939 $z click for full text (PQDT)