國立虎尾科技大學 |

Development of Back Contacts for CdTe Thin Films Solar Cells.

Record Type:	Language materials, manuscript : Monograph/item
Title/Author:	Development of Back Contacts for CdTe Thin Films Solar Cells./
Author:	Alfadhili, Fadhil Khalaf Dahash.
Description:	1 online resource (116 pages)
Notes:	Source: Dissertations Abstracts International, Volume: 82-12, Section: B.
Contained By:	Dissertations Abstracts International82-12B.
Subject:	Physics. -
Online resource:	click for full text (PQDT)
ISBN:	9798516076732

Development of Back Contacts for CdTe Thin Films Solar Cells.
Alfadhili, Fadhil Khalaf Dahash.

Development of Back Contacts for CdTe Thin Films Solar Cells. - 1 online resource (116 pages)

Source: Dissertations Abstracts International, Volume: 82-12, Section: B.

Thesis (Ph.D.)--The University of Toledo, 2020.

Includes bibliographical references

Thin film solar cells based on polycrystalline p-type cadmium telluride (CdTe) represent one of these the most promising photovoltaic (PV) device due to high efficiency and low-cost production. Currently, CdTe solar cells provide the lowest cost electricity generation in utility-scale applications, which is a cost-competitive with the traditional power source, fossil fuel. CdTe thin film PV has attained 22.1 % of power conversion efficiency for small area scale and 18.6 % for modules scale. However, the high efficiency of CdTe devices has been achieved by increasing the photo-generated current by changing the traditional window layer (CdS) of CdTe to a wider bandgap material with better band alignment. The open-circuit voltage (VOC) remains below the theoretical limit due to a barrier at the back of the device due to the deep valence band edge of CdTe (-5.9 eV). Voc can be increased by adding a buffer layer between CdTe and the back electrode to decrease band banding and reducing carrier recombination at the back interface. In this thesis, several materials were investigated as a back-buffer layer, such as single-wall carbon nanotube (SWCNT), zinc telluride (ZnTe), tellurium (Te), and cadmium zinc telluride (CZT) to minimize the bend bending at CdTe/back-buffer layer interface. An alternative method to reduce the carrier recombination at the rear surface, the use of aluminum oxide (Al2O3) layer as a passivation layer was also demonstrated. Finally, an effective method of CdCl2 treatment for CZT thin film was investigated. This method shows that zinc (Zn) can be maintained during the heat treatment.

Electronic reproduction.
Ann Arbor, Mich. :
ProQuest,
2024

Mode of access: World Wide Web

ISBN: 9798516076732Subjects--Topical Terms:

564049
Physics.
Subjects--Index Terms:

Thin film solar cellsIndex Terms--Genre/Form:

554714
Electronic books.

Development of Back Contacts for CdTe Thin Films Solar Cells.
LDR:02933ntm a22003617 4500 001 1145440
005 20240624103651.5
006 m o d
007 cr bn ---uuuuu
008 250605s2020 xx obm 000 0 eng d
020 $a 9798516076732
035 $a (MiAaPQ)AAI28642546
035 $a (MiAaPQ)OhioLINKtoledo1588962981116943
035 $a AAI28642546
040 $a MiAaPQ $b eng $c MiAaPQ $d NTU
100 1 $a Alfadhili, Fadhil Khalaf Dahash. $3 1437663
245 1 0 $a Development of Back Contacts for CdTe Thin Films Solar Cells.
264 0 $c 2020
300 $a 1 online resource (116 pages)
336 $a text $b txt $2 rdacontent
337 $a computer $b c $2 rdamedia
338 $a online resource $b cr $2 rdacarrier
500 $a Source: Dissertations Abstracts International, Volume: 82-12, Section: B.
502 $a Thesis (Ph.D.)--The University of Toledo, 2020.
504 $a Includes bibliographical references
520 $a Thin film solar cells based on polycrystalline p-type cadmium telluride (CdTe) represent one of these the most promising photovoltaic (PV) device due to high efficiency and low-cost production. Currently, CdTe solar cells provide the lowest cost electricity generation in utility-scale applications, which is a cost-competitive with the traditional power source, fossil fuel. CdTe thin film PV has attained 22.1 % of power conversion efficiency for small area scale and 18.6 % for modules scale. However, the high efficiency of CdTe devices has been achieved by increasing the photo-generated current by changing the traditional window layer (CdS) of CdTe to a wider bandgap material with better band alignment. The open-circuit voltage (VOC) remains below the theoretical limit due to a barrier at the back of the device due to the deep valence band edge of CdTe (-5.9 eV). Voc can be increased by adding a buffer layer between CdTe and the back electrode to decrease band banding and reducing carrier recombination at the back interface. In this thesis, several materials were investigated as a back-buffer layer, such as single-wall carbon nanotube (SWCNT), zinc telluride (ZnTe), tellurium (Te), and cadmium zinc telluride (CZT) to minimize the bend bending at CdTe/back-buffer layer interface. An alternative method to reduce the carrier recombination at the rear surface, the use of aluminum oxide (Al2O3) layer as a passivation layer was also demonstrated. Finally, an effective method of CdCl2 treatment for CZT thin film was investigated. This method shows that zinc (Zn) can be maintained during the heat treatment.
533 $a Electronic reproduction. $b Ann Arbor, Mich. : $c ProQuest, $d 2024
538 $a Mode of access: World Wide Web
650 4 $a Physics. $3 564049
653 $a Thin film solar cells
653 $a Cadmium telluride
653 $a Cadmium zinc telluride
653 $a Photvoltaics
655 7 $a Electronic books. $2 local $3 554714
690 $a 0605
710 2 $a ProQuest Information and Learning Co. $3 1178819
710 2 $a The University of Toledo. $b Physics. $3 1437664
773 0 $t Dissertations Abstracts International $g 82-12B.
856 4 0 $u http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=28642546 $z click for full text (PQDT)